The ultimate pedal for enduro racing and riding. The mallet E was developed with the help some well known enduro athletes. 12% smaller than the Mallet DH pedals but with many of its well loved features. There are 2 different axle lengths available 52mm or 57mm (the 57mm pedal is only available in a half black/half blue colour option). The 52mm will provide an engagement point and Q factor similar to other brands of pedals. If you have been previously using the Mallet DH pedal you may benefit from using the longer axle version. Riders who prefer a wider Q factor / have less crankarm / pedal clearance may also benefit from the longer axle pedals. Concave pedal platform for secure foothold. Like it’s DH equivalent you get that flat pedal feel whilst running clipless. 49g lighter and 12% smaller pedal body than the crankbrothers Mallet DH pedal with a 52mm Q-Factor compared to 57mm on the DH equivalent. Ribbed body allows for better traction when unclipped Chamfered edges for reduction in rock strikes Excellent mud-shedding: the design is very open. 4-sided entry: clip in on all 4 sides of the pedal by pushing forward or pulling backwards on the pedal. Increased float: 6° of side-to-side rotational play. The float of the pedal allows for the rider to shift positions on the bike while keeping their feet clipped into the pedal. This allows for improved rider control and bike handling. Fit adjustment: crankbrothers premium cleats can be adjusted for either 15° or 20° release angle. Zero-float cleats can be purchased separately (link to these). Customise the fit between your shoe/pedal interface by using integrated traction pads. The pedals come with the 1mm tread pads fitted and include set of 2mm pads in the box. Outer enduro cartridge bearing is designed specifically for pedals. Enduro use superior materials grease and sealing on their bearings which are designed especially for use on a bike. Inner igus LL-glide bearing has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails. Double seal system combines a double lip internal seal and a new external seal to keep water and debris from entering the pedal. crankbrothers pedals are fully re-buildable for simple maintenance. There is a consistency in parts across all pedal models which allows for ease of servicing this is easily done using the pedal refresh kit (CRB-16051). Specification Weight (per pair): 419g Spindle: Forged scm 435 chromoly steel Body: 6061-T6 aluminium Wings: 17-4PH stainless Spring: 300 series stainless steel Inner bearing: Igus LL-glide bearing Outer bearing: Enduro cartridge bearing Pins: 12 pins per pedal Cleats: Premium brass cleats included Release angle: 15° or 20° Warranty: 5 years
The crankbrothers candy is an iconic pedal designed by Carl and Frank the original founders of crankbrothers they were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated….It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. The Candy is really diverse and is used by a wide range of riders. We have seen them out on the trail at cyclocross races and even on commuter bikes. The cage around the 4 point engagement system inspires confidence and offers a great alternative to the eggbeater pedal if you want more of a pedal body surface area. Cleat: Premium brass cleats included Shims: Included Release Angle: 15° to 20° Warranty: 2 years Weight: 272g per pair Spindle: Forged scm435 chromoly steel Body: one piece composite Wings: Stamped steel Spring: 300 series stainless steel Inner bearing: Bushing Outer bearing: Cartridge Maximum rider weight: No restrictions Colours: Black Blue Red or Neon Green As with the rest of the crankbrothers range the pedals are fully serviceable with a level 1 / 2 service kit (product code CRB-11729). Servicing is simple and does not require any specialist tools just a flat head screwdriver socket wrench and 8mm allen key to hold the pedal by the axle. We recommend that the pedal is cleaned and greased every 30 hours of riding and the bearings are inspected for wear.
The design for the original crankbrothers pedal began out of frustration. The founders of crankbrothers Carl and Frank were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated…. It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. The candy 7 pedal is a clipless pedal with a platform offering improved stability across a wide range of disciplines from all mountain / trail to cyclo-cross. The pedal body is 10% larger than the level 1 2 and 3 pedal bodies. The chamfered edges help to minimise rock strikes. There is an ongoing debate amongst many riders about which is best candy or eggbeater. The candy pedal provides an additional platform which is confidence inspiring and also gives some support or those moments when you’ve unclipped but are unsure if you need to get your foot down for a dab jump off the bike or quickly get clipped in again and put the power down. Excellent mud-shedding: the design is very open. Ribbed body for extra traction when unclipped 4-sided entry: clip in on all 4 sides of the pedal by pushing forward or pulling backwards on the pedal. Increased float: 6° of side-to-side rotational play. The float of the pedal allows for the rider to shift positions on the bike while keeping their feet clipped into the pedal. This allows for improved rider control and bike handling. Fit adjustment: crankbrothers premium cleats can be adjusted for either 15° or 20° release angle. Zero-float cleats can be purchased separately (link to these). Customise the fit between your shoe/pedal interface by using integrated traction pads. The pedals come with the 1mm tread pads fitted and include set of 2mm pads in the box. Chamfered edges help reduce rock strikes Outer enduro cartridge bearing is designed specifically for pedals. Enduro use superior materials grease and sealing on their bearings which are designed especially for use on a bike. Inner igus LL-glide bearing has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails. Double seal system combines a double lip internal seal and a new external seal to keep water and debris from entering the pedal. crankbrothers pedals are fully re-buildable for simple maintenance. There is a consistency in parts across all pedal models which allows for ease of servicing this is easily done using the pedal refresh kit (CRB-16051). candy 7 Weight (per pair) 320g Spindle Forged scm 435 chromoly steel Body 6061-T6 aluminium Wings 17-4PH stainless Spring 300 series stainless steel inner bearing Igus LL-glide bearing outer bearing Enduro cartridge bearing Cleats premium brass cleats included release angle 15° or 20° Warranty 5 years
The crankbrothers candy is an iconic pedal designed by Carl and Frank the original founders of crankbrothers they were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated….It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. The Candy is really diverse and is used by a wide range of riders. We have seen them out on the trail at cyclocross races and even on commuter bikes. The cage around the 4 point engagement system inspires confidence and offers a great alternative to the eggbeater pedal if you want more of a pedal body surface area. The trade up from level 1 pedals is the 2 piece machined aluminium pedal body and increased warranty to 5 years. Cleat: Premium brass cleats included Shims: Included Release Angle: 15° to 20° Warranty: 5 years Weight: 324g per pair Spindle: Forged scm435 chromoly steel Body: 2 piece machined aluminium Wings: Stamped steel Spring: 300 series stainless steel Inner bearing: Bushing Outer bearing: Cartridge Maximum rider weight: No restrictions Colours: Orange/Silver or Silver You can customise the fit and feel of your pedal using crankbrothers tread contact sleeves (CRB-13282). These shims come with 3 different thicknesses enabling the rider to ensure good contact between their shoes and the pedal axle (as the tread wears down the contact can move away from the axle and onto the wings of the pedal). As with the rest of the crankbrothers range the pedals are fully serviceable with a level 1 / 2 service kit (product code CRB-11729). Servicing is simple and does not require any specialist tools just a flat head screwdriver socket wrench and 8mm allen key to hold the pedal by the axle. We recommend that the pedal is cleaned and greased every 30 hours of riding and the bearings are inspected for wear.
The original crankbrothers tool range. Compact and lightweight tools for any eventuality. Whether its making a minor adjustment or an on the trail repair these tools have you covered. Frame: 6061-T6 aluminium Tools: 6150 high tensile steel Warranty: Lifetime Weight: 175g Length: 3.5' / 89mm Chain tool: 8/9/10 speed compatible Spoke wrench: #0 1 2 3 Hex wrenches: #2 2.5 3 4 5 6 8 Screwdrivers: 2-phillips 1-flat Open wrench: 8mm 10mm Torx: T-25 T-10 Carrying case: Stainless and polymer
Crank Brothers design and quality in an affordable package. Reversible head is compatible with Presta & Schrader valves. Large dual piston allows 2 effortless modes 1-40 psi high volume and 40-100psi high pressure. Material: 6061-T6 aluminium Pressure: 130psi / 9bar Air switch: High volume / high pressure Mounting bracket: Not included Warranty: 5 years Weight: 128g Length: 176mm
The crankbrothers eggbeater is an iconic pedal designed by Carl and Frank the original founders of crankbrothers they were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated….It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. The eggbeater's simple design gives the advantage of amazing mud shedding and 4 points of entry making it perfect for XC trail riding and cyclo cross. Cleat: Premium brass cleats included Shims: Included Release Angle: 15° to 20° Warranty: 5 years Weight: 280g per pair Spindle: Forged scm435 chromoly steel Body: cast stainless steel Wings: stamped stainless steel Spring: 300 series stainless steel Inner bearing: Bushing Outer bearing: Cartridge Maximum rider weight: No restrictions Special edition colours: Silver/Black You can customise the fit and feel of your pedal using crankbrothers tread contact sleeves (CRB-13282). They come with 3 different thicknesses enabling the rider to ensure good contact between their shoes and the pedal axle (as the tread wears down the contact can move away from the axle and onto the wings of the pedal). You may also like to run the pedals on your road / commuter bike. Buy a set of Quattro cleats (CRB-15289) to use on your road shoes. It makes pulling off from junctions a breeze as you have 4 points of entry to the pedals. As with the rest of the crankbrothers range the pedals are fully serviceable with a level 1 / 2 service kit (product code CRB-11729). Servicing is simple and does not require any specialist tools just a flat head screwdriver socket wrench and 8mm allen key to hold the pedal by the axle. We recommend that the pedal is cleaned and greased every 30 hours of riding and the bearings are inspected for wear.
Designed for use with quattro eggbeater and candy pedals. Enables you to use crankborthers pedals with 3 bolt cleat fitting road shoes. Composite platform and brass cleat Float: 6 degrees Release angle: 15 or 20 degrees Bolt pattern: 3 bolt
Ultra durable brass cleats for eggbeater candy smarty acid and mallet pedals. Premium strength brass Release angle: 15 degrees Bolt pattern: 2 bolt Adjustment: 2.2mm left/right Shims included
Ultra durable brass cleats for crankbrother pedals. Premium strength brass Release angle: 10 degrees Bolt pattern: 2 bolt Adjustment: 2.2mm left/right Shims included
The crankbrothers candy is an iconic pedal designed by Carl and Frank the original founders of crankbrothers they were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated….It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. The Candy is really diverse and is used by a wide range of riders. We have seen them out on the trail at cyclocross races and even on commuter bikes. The cage around the 4 point engagement system inspires confidence and offers a great alternative to the eggbeater pedal if you want more of a pedal body surface area. Cleat: Premium brass cleats included Shims: Included Release Angle: 15° to 20° Warranty: 5 years Weight: 304g per pair Spindle: Forged scm435 chromoly steel Body: 2 piece machined aluminium Wings: Cast Steel Spring: 300 series stainless steel Inner bearing: Needle Outer bearing: Cartridge Maximum rider weight: No restrictions Colour options: Black/Silver Blue/Silver or Red/Silver You can customise the fit and feel of your pedal using crankbrothers tread contact sleeves (CRB-13282). These shims come with 3 different thicknesses enabling the rider to ensure good contact between their shoes and the pedal axle (as the tread wears down the contact can move away from the axle and onto the wings of the pedal). As with the rest of the crankbrothers range the pedals are fully serviceable with a level 3 / 11 service kit (product code CRB-11730). Servicing is simple and does not require any specialist tools just a flat head screwdriver socket wrench and 8mm allen key to hold the pedal by the axle. We recommend that the pedal is cleaned and greased every 30 hours of riding and the bearings are inspected for wear.
Choose to ride flat or clipped in. The new double shot is crankbrothers hybrid pedal designed half flat/half clip-in. Moulded traction pins and diamond plate area provide grip and support. Excellent mud-shedding: machined pedal body helps further prevent mud clogging. Fit adjustment: crankbrothers premium cleats can be adjusted for either 15° or 20° release angle. Zero-float cleats can be purchased separately (link to these). Internals run on igus LL-glide bearing which has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails. Double seal system combines a double lip internal seal and a new external seal to keep water and debris from entering the pedal. Double shot Weight (per pair) 395g Spindle Forged scm 435 chromoly steel Body A380 aluminum Wings Stamped steel Spring 300 series stainless steel inner bearing Igus LL-glide bearing Cleats premium brass cleats included Pins Moulded traction pins release angle 15° or 20° Warranty 5 years
The eggbeater's simple design gives the advantage of amazing mud shedding and 4 points of entry making it perfect for XC trail riding and cyclo cross. The crankbrothers eggbeater is an iconic pedal designed by Carl and Frank the original founders of crankbrothers they were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated….It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. Cleat: Premium brass cleats included Shims: Included Release Angle: 15° to 20° Warranty: 2 years Weight: 286g per pair Spindle: Forged scm435 chromoly steel Body: stamped steel Wings: Stamped steel Spring: 300 series stainless steel Inner bearing: Bushing Outer bearing: Cartridge Maximum rider weight: No restrictions Colours: Silver/Black or Silver/Red As with the rest of the crankbrothers range the pedals are fully serviceable with a level 1 / 2 service kit (product code CRB-11729). Servicing is simple and does not require any specialist tools just a flat head screwdriver socket wrench and 8mm allen key to hold the pedal by the axle. We recommend that the pedal is cleaned and greased every 30 hours of riding and the bearings are inspected for wear.
The eggbeater's simple design gives the advantage of amazing mud shedding and 4 points of entry making it perfect for XC trail riding and cyclo cross. The crankbrothers eggbeater is an iconic pedal designed by Carl and Frank the original founders of crankbrothers they were tired of getting stuck in mud-covered pedals with no way in or out. They realised that existing pedals were too complicated….It started with a simple question: what is the best way to attach a shoe to a crank? To answer this question Carl and Frank created a system with only two moving parts hinging on a spring. This system became known as the eggbeater pedal and later it was adapted into the candy pedal. Cleat: Premium brass cleats included Shims: Included Release Angle: 15° to 20° Warranty: 5 years Weight: 278g per pair Spindle: Forged scm435 chromoly steel Body: cast stainless steel Wings: cast stainless steel Spring: 300 series stainless steel Inner bearing: Needle Outer bearing: Cartridge Maximum rider weight: No restrictions Colours options: Silver/Blue or Silver/Red You can customise the fit and feel of your pedal using crankbrothers tread contact sleeves (CRB-13282). They shims come with 3 different thicknesses enabling the rider to ensure good contact between their shoes and the pedal axle (as the tread wears down the contact can move away from the axle and onto the wings of the pedal). You may also like to run the pedals on your road / commuter bike. Buy a set of Quattro cleats (CRB-15289) to use on your road shoes. It makes pulling off from junctions a breeze as you have 4 points of entry to the pedals. As with the rest of the crankbrothers range the pedals are fully serviceable with a level 3 / 11 service kit (product code CRB-11730). Servicing is simple and does not require any specialist tools just a flat head screwdriver socket wrench and 8mm allen key to hold the pedal by the axle. We recommend that the pedal is cleaned and greased every 30 hours of riding and the bearings are inspected for wear.
Mallet pedals feature a double sided open design allowing for quick and reliable engagement with minimal mud clogging. A two piece body keeps the weight down whilst providing a strong and durable platform. Release angle: 15° to 20° Cleat: Premium brass cleats included Warranty: 5 years Weight: 428g per pair Platform: Two piece aluminium + composite Wings: Stamped steel Spring: 300 series stainless steel Spindle: Forged scm435 chromoly steel Inner bearing: Bushing Outer bearing: Cartridge Traction pins: 8mm adjustable
Mallet pedals feature a double sided open design allowing for quick and reliable engagement with minimal mud clogging. A two piece body keeps the weight down whilst providing a strong and durable platform. Release angle: 15° to 20° Cleat: Premium brass cleats included Warranty: 5 years Weight: 435g per pair Platform: Two piece aluminium + composite Wings: Investment cast steel Spring: 300 series stainless steel Spindle: Forged scm435 chromoly steel Inner bearing: Needle Outer bearing: Cartridge Traction pins: 8mm adjustable
The ultimate pedal for enduro racing and riding.The mallet E was developed with the help some well known enduro athletes. 12% smaller than the Mallet DH pedals but with many of its well loved features. There are 2 different axle lengths available 52mm or 57mm (the 57mm pedal is only available in a half black/half blue colour option). The 52mm will provide an engagement point and Q factor similar to other brands of pedals. If you have been previously using the Mallet DH pedal you may benefit from using the longer axle version. Riders who prefer a wider Q factor / have less crankarm / pedal clearance may also benefit from the longer axle pedals. Available in black or blue colour options with the standard 52mm axle or half black / half blue with the longer 57mm axle. Concave pedal platform for secure foothold. Like it’s DH equivalent you get that flat pedal feel whilst running clipless. 49g lighter and 12% smaller pedal body than the crankbrothers Mallet DH pedal with a 52mm Q-Factor compared to 57mm on the DH equivalent. Ribbed body allows for better traction when unclipped Chamfered edges for reduction in rock strikes Excellent mud-shedding: the design is very open. 4-sided entry: clip in on all 4 sides of the pedal by pushing forward or pulling backwards on the pedal. Increased float: 6° of side-to-side rotational play. The float of the pedal allows for the rider to shift positions on the bike while keeping their feet clipped into the pedal. This allows for improved rider control and bike handling. Fit adjustment: crankbrothers premium cleats can be adjusted for either 15° or 20° release angle. Zero-float cleats can be purchased separately (link to these). Customise the fit between your shoe/pedal interface by using integrated traction pads. The pedals come with the 1mm tread pads fitted and include set of 2mm pads in the box. Outer enduro cartridge bearing is designed specifically for pedals. Enduro use superior materials grease and sealing on their bearings which are designed especially for use on a bike. Inner igus LL-glide bearing has been exclusively formulated for crankbrothers. It performs in even the most adverse conditions out on the trails. Double seal system combines a double lip internal seal and a new external seal to keep water and debris from entering the pedal. crankbrothers pedals are fully re-buildable for simple maintenance. There is a consistency in parts across all pedal models which allows for ease of servicing this is easily done using the pedal refresh kit (CRB-16051). Mallet E Weight (per pair) 419g Spindle Forged scm 435 chromoly steel Body 6061-T6 aluminium Wings 17-4PH stainless Spring 300 series stainless steel inner bearing Igus LL-glide bearing outer bearing Enduro cartridge bearing Pins 12 pins per pedal Cleats premium brass cleats included release angle 15° or 20° Warranty 5 years
The original Cranks Brother’s tool range. Compact and lightweight tools for any eventuality. Whether its making a minor adjustment or an on the trail repair these tools have you covered. Frame: 6061-T6 aluminium Tools: 6150 high tensile steel Warranty: Lifetime Weight: 85g Length: 3.5' / 89mm Hex wrenches: #3 4 5 6 Screwdrivers: Phillips
The lightest dual clamp lock-on grips available. Ideal for XC racing. Weight: 65g Width: 130mm Grip material: High density foam Lock rings: 6061 T-6 aluminium Torx bolt size: T10
Sleeves snap on to the next gen candy and eggbeaters to tighten the interface between the shoe and pedal. Includes: 1mm 2mm 3mm sleeves Compatible with candy and eggbeater 11 3 and 2