Search found 1947 products for nukeproof

Nukeproof Neutron V2 Front Wheel Front Wheels
  • £104.99
  • RRP £119.99
  • Saving you £13

This front wheel features a Nukeproof Neutron front hub that is available for both 15mm or 20mm spacings in both Boost and non-Boost. Nukeproof also sell end caps for QR (available separately). The 6066 alloy rim has been extensively to ensure it is a rim which is light enough for aggressive trail riding but strong enough for DH. Nukeproof have used J-Bend spokes meaning tensioning and spoke replacement is much simpler than using a straight pull spoke. The wheels come taped with tubeless valve installed so all you need to do is add sealant and your tyre to get a finished tubeless setup. The valve supplied is Nukeproofs Horizon valve which also has a core remover built into the cap. This valve is also compatible with tyre inserts like Nukeproof ARD. Spoke lengths on the front wheels are the same regardless of spacing, the length changes with wheel size: Wheel               Wheel Size            Non Driveside Spoke Length            Driveside Spoke Length Front                      27.5"                                    272                                              273 Front                      29"                                       291                                              292 Conversion kits and replacement end caps available separately. Please click here to view how to change your hub spacing with end caps. Full range of spare parts available.

VIEW ITEM
Nukeproof Neutron V2 Freehub Body 36t Wheel Hub Spares
  • £44.99

A new hub seal and bushing is supplied with Nukeproof freehubs. To avoid damage to the hub seal, turn the freehub anti-clockwise as you fit. Please Note: The new hub seal will be fitted to the freehub for transport purposes. This needs to be removed from the freehub by pressing the pawls BEFORE fitting the freehub. Options: Shimano HG Shimano Microspline SRAM XD If you have a HG / XD hub and want to convert to microspline, you will need Nukeproof's microspline conversion kit which can be found here. For step-by-step fitting instructions click here. Freehubs: Installation Instructions: 1. Remove driveside end cap 2. Pull off old freehub turning anticlockwise as you pull 3. Check hub seal for damage, if it is damaged remove the seal 4. If seal was removed, press on new seal 5. Apply grease hub ratchet ring 6. Apply thin grease to freehub pawls & springs then push onto hub shell turning anticlockwise 7. Refit driveside end cap

VIEW ITEM
Nukeproof Neutron V2 Rear Axle Wheel Spares
  • £11.99

142mm, 148mm and 150mm axle options available. You will need to choose the correct axle to suit your hub spacing. Please note that the 148mm axle you require will depend if you are using a HG / XD or Microspline freehub.

VIEW ITEM
Nukeproof Horizon V2 End Caps Wheel Hub Spares
  • £11.99

These end caps can be used to convert your hub to a different spacing or replace a lost cap. This makes them perfect as a replacement or for riders who want to transform their hub set-up. Compatibility Chart & How to Fit End Caps Click here to determine which hubs can be converted, as the caps only fit the original specific hub options. End Caps: Changing end caps is simple and no tools are required. Just pull off the end caps on the hub and then push the new ones on. Where the end caps are not identical, the non-driveside always has the wider flange to cover the bearing.  All caps sold as pairs and only compatible with Nukeproof Horizon V2 hubs

VIEW ITEM
Nukeproof Neutron V2 End Caps Wheel Hub Spares
  • £11.99

These end caps can be used to convert your hub to a different spacing or replace a lost cap. Compatibility Chart & How to Fit End Caps Please click here to determine which hubs can be converted, as the caps only fit the original specific hub options. End Caps: Changing end caps is simple and no tools are required. Just pull off the end caps on the hub and then push the new ones on. Where the end caps are not identical, the non-driveside always has the wider flange to cover the bearing. All caps sold as pairs and only compatible with Nukeproof Neutron V2 hubs.

VIEW ITEM
Nukeproof Neutron V2 Rear Wheel 36t Back Wheels
  • £144.99
  • RRP £169.99
  • Saving you £15

This rear wheel features 36 points of engagement and comes in a range of freehub options. Nukeproof has also made freehubs available separately and easy to change if you choose to upgrade your drivetrain in the future. The 142mm hub can be converted to 135mm QR and the 148mm HG / XD hub can be converted to 141mm using end caps. The hub has been machined to remove excess material and make it as strong and light as possible. Nukeproof have increased the thickness of pawl springs in these hubs to give secure engagement on every pedal stroke. The 6066 alloy rim has been extensively to ensure it is a rim which is light enough for aggressive trail riding but strong enough for DH. Nukeproof have used J-Bend spokes meaning tensioning and spoke replacement is much simpler than using a straight pull spoke. The wheels come taped with tubeless valve installed so all you need to do is add sealant and your tyre to get a finished tubeless setup. The valve supplied is Nukeproof's Horizon valve which also has a core remover built into the cap. This valve is also compatible with tyre inserts like Nukeproof ARD. Spoke lengths on the front wheels are the same regardless of spacing, the length changes with wheel size: Wheel Size       Spacing                             Non Driveside Spoke Length        Driveside Spoke Length 27.5"            142mm / 148mm x 12mm                 274                                            272 27.5"            150mm / 157mm x 12mm                 274                                            273 29"               142mm / 148mm x 12mm                 292                                            290 29"               150mm / 157mm x 12mm                 292                                            291 Conversion kits and replacement end caps available separately. Caps                            Nukeproof Part Number                Replacement or Conversion Rear 135mm QR         NUKNEUV2R135CAPS           Convert Non Boost 142mm hub to QR Rear 141mm               NUKNEUV2R141BCAPS        Convert Boost 148mm HG / XD hub to 141mm QR (It is not possible to convert Nukeproof's 148mm microspline hubs to QR) Rear 142/148/157mm NUKNEUV2R148CAPS           Replacement caps for 142mm, 148mm and 157mm Rear 150mm               NUKNEUV2R150CAPS           Replacement 150mm caps Full range of spare parts available.

VIEW ITEM
Nukeproof Horizon V2 Freehub Body 102t Wheel Hub Spares
  • £49.99

This freehub body features a tough alloy construction, which makes it perfect for replacing your old or worn-out existing model. Suitable for use only on Nukeproof Horizon V2 hubs, this freehub body is designed for quick and easy installation. Options: ·         Shimano HG ·         Shimano Microspline ·         SRAM XD A new hub seal and bushing is supplied with Nukeproof freehubs. Please Note: The new hub seal will be fitted to the freehub for transport purposes. This needs to be removed from the freehub by pressing the pawls BEFORE fitting the freehub. Microspline freehubs also include the driveside end cap so you can easily convert an HG / XD hub to microspline If you are converting a microspline hub to XD or HG, you will also require a new driveside end cap which can be bought here ( ) This freehub is only compatible with Nukeproof Horizon V2 hubs. For step-by-step fitting instructions click here. Freehubs: Installation Instructions: 1. Remove driveside end cap 2. Pull off old freehub turning anticlockwise as you pull 3. Check hub seal for damage, if it is damaged remove the seal 4. If seal was removed, press on new seal 5. Apply grease hub ratchet ring 6. Apply thin grease to freehub pawls & springs then push onto hub shell turning anticlockwise 7. Refit driveside end cap

VIEW ITEM
Nukeproof Horizon V2 Front Wheel Front Wheels
  • £129.99
  • RRP £149.99
  • Saving you £13

Ready for fast-paced and aggressive trail-riding, this front wheel has gone through extensive testing to meet the demands of both Enduro and DH riders. It features a special blend of alloy material, which produces a hardness similar to 7-series alloy, but with the ductility and yield properties of a 6-series. This gives you the best of both worlds in terms of stiffness, strength and weight. Nukeproof has also ensured this front wheel's rim profile is the same as the rear (sold separately), the only difference is the front has a thinner sidewall for greater weight savings. One final highlight is it comes equipped with J-bend spokes, which means that tensioning and spoke replacement is as simple as possible. Enduro ABEC 5 Bearings After extensive testing with various brands of bearings, Nukeproof chose to use Enduro ABEC 5 bearings in this front wheel. These bearings have the “LLU/LLB” seal type, which uses two lips that make light contact in a groove to create a labyrinth where the water or dirt has a more difficult time to penetrate. LLU seals are similar, only the contact pressure or interference fit is greater to seal better. Enduro bearings have 80% grease fill on both sides whereas most other bearings have 35% grease fill on one side. This delivers full coverage, so there are no dry areas as well as avoiding metal on metal contact or wear. This means that the axle feels tight out of the box and after a couple of rides it will become free. Nukeproof Horizon V2 Hub This MTB front wheel features a revised Nukeproof Horizon V2 hub, which is available for both 15mm & 20mm spacings in both boost & non boost. We also sell end caps for QR separately.  What's Included? Wheels come taped with tubeless valve installed so all you need to do is fit your tyre and add sealant. The tubeless valve supplied is the new Nukeproof Horizon valve which is compatible with Nukeproof ARD and other tyre inserts as well as the cap having a core remover built in. Spoke length’s on Nukeproof wheels are the same regardless of spacing, the length changes with wheel size: Wheel          Wheel Size          Non Drive Side Spoke Length          Driveside Spoke Length Front                 27.5"                                    269                                                 270 Front                 29"                                       288                                                 289   Conversion kits and replacement end caps available separately. Please click here to view how to change your hub spacing with end caps.

VIEW ITEM
Nukeproof Neutron V2 Pawls & Springs Wheel Hub Spares
  • £9.99

This set contains four pawls and four springs, plus a plastic cover for the freehub.

VIEW ITEM
Nukeproof Neutron V2 Microspline Conversion Kit Wheel Hub Spares
  • £54.99

This kit contains all the parts needed to convert your 148mm Nukeproof Neutron HG / XD hub to have a microspline freehub. Please note this kit requires the hub to be stripped, a step by step guide to do this can be found here.

VIEW ITEM
Nukeproof Horizon Neutron V2 Non Drive Hub Seal Wheel Hub Spares
  • £1.99

This non-driveside seal fits all Nukeproof Horizon and Neutron v2 rear hubs. Hub Seal Changing this seal is easy by following the instructions below: 1. Remove non-driveside end cap 2. Take a thin flat head screwdriver and gently prize off the old seal 3. Push new seal in place 4. Refit non-driveside end cap

VIEW ITEM
Nukeproof Universal Presta Tubeless Valves - Pair Tyre Spares
  • £17.99
  • RRP £19.99
  • Saving you £10

Featuring an adapted head which allows the tyre insert to sit on top of the valve, the shape of the head allows for easy inflation and deflation. Each valve has a removable core allowing you to get maximum air flow from your tubeless pump or CO2 cartridge. The specially-designed custom cap features a core remover built in so you can remove & tighten the core without any additional tools. The nut has also been designed so that you can get a good grip on the flat edges to tighten the valve in the rim. An O-ring is also provided which sits against the outside of the rim and provides an airtight seal while preventing damage to the rim from the nut on the valve. How to Install Remove valve cap and nut, insert valve through rim, fit O-ring to valve then thread nut on and tighten by hand.

VIEW ITEM
Nukeproof Dissent Seat Stay Protector Frame Protectors
  • £7.99

Designed for Nukeproof Dissent, this genuine Nukeproof Dissent seat stay is a superb barrier against the splashes, scrapes and scratches thrown up by the elements thanks to its durable moulded silicone construction. It attaches to your seat stay via its 3M adhesive backing, making this Dissent seat stay protector the ideal guard against all types of debris, dings and damage.

VIEW ITEM
Nukeproof Dissent 275 Chain Stay Protector Frame Protectors
  • £9.99

Designed for the current Dissent 275 model, this genuine Nukeproof chain stay protector provides exceptional protection. Engineered from a durable moulded silicone and attaches to your frame's chainstays via the 3M adhesive backing, the Dissent 275 Chain Stay Protector is the ideal barrier against bangs, dings, dirt and chain slap.

VIEW ITEM
Nukeproof Reactor Carbon Chain Stay Protector 290 Frame Protectors
  • £9.99

Designed to fit 2020 Nukeproof Reactor Carbon 290 models, this genuine Nukeproof protector is an outstanding barrier, built from a durable moulded silicone construction. Attaching to your chainstay by its 3M adhesive backing, this protector is the ideal barrier against dings, dirt and damage.

VIEW ITEM
Nukeproof Dissent 290 Chain Stay Protector Frame Protectors
  • £9.99

Designed for the 2020 Nukeproof Dissent 290, this genuine Nukeproof chain stay protector provides exceptional protection and mounts perfectly thanks to its durable moulded silicone construction. It attaches you to your frame's chainstays via the 3M adhesive backing and is the ideal barrier against bangs, grit, rocks, dirt and chain slap. 

VIEW ITEM
Nukeproof Reactor Seat Stay Protector Frame Protectors
  • £7.99

Compatible with 2020-2022 Alloy and Carbon 275 and 290 models, this genuine Nukeproof Reactor seat stay is a superb barrier against the splashes, scrapes and scratches thrown up by the elements thanks to its durable moulded silicone construction. It attaches to your seat stay via its 3M adhesive backing, making this Reactor seat stay protector the ideal guard against all types of debris, dings and damage.

VIEW ITEM
Nukeproof Reactor Carbon Chain Stay Protector 275 Frame Protectors
  • £9.99

Designed to fit 2020 Nukeproof Reactor Carbon 275 models, this genuine Nukeproof protector is an outstanding barrier, built from a durable moulded silicone construction. Attaching to your chainstay by its 3M adhesive backing, this protector is the ideal barrier against dings, dirt and damage.

VIEW ITEM
Nukeproof Kevlar Chainstay Protector Frame Protectors
  • £4.49
  • RRP £8.99
  • Saving you £50

Attached and held in place via a Velcro closure running the length of the material and to ensure it stays securely in place it has anti-slip rubber panel on the back. As this chainstay protector is exceptionally robust, it is slightly less elastic than traditional neoprene chainstay protectors so you would need to measure your frame chainstay accurately in order to ensure you get the correct size to fit your frame.

VIEW ITEM
Nukeproof Sam Hill Enduro Race Grip Super Soft Bar Grips
  • £19.99

These grips feature a soft, very grippy compound, which makes them perfect for long days riding and sure to provide excellent grip regardless of the weather conditions. These grips have been used by Sam when riding the toughest stages in the world of MTB racing, in the most demanding conditions. Featuring an Enduro race compound, these grips are designed for enduro race days to give excellent grip and comfort, this does mean they will wear quicker than the A15 Sam Hill Grips. Perfect for World Level Racing and Weekend Trail Sessions Alike Nukeproof and Sam Hill work together to create World Level products that everyone can use. The Sam Hill Enduro Race Grip was first used by Sam in round 4 of the 2018 Enduro World Series (EWS) where he took the win and has been using them ever since. After that race, he described the compound as “extra extra soft, semi throttle durometer” and described the grips as “pretty comfortable little things”. With comments like that we knew we were onto a winner with these grips. Nukeproof Sam Hill Enduro Race Grip installation instructions are available for download HERE.

VIEW ITEM
expand_less