Park Tool Spoke, Bearing and Cotter Gauge SBC-1This handy shop aid is ideal for sizing spokes, ball bearings and crank cotters. To use, just hang the head of the spoke in the oblong hole and read its length on the scale.For crank cotters and ball bearings it works just like a gauge for drill bits. Spoke lengths are in both metric and fractional markings. Made of anodized aluminum with embossed markings to allow easy reading and long life.Buy Park Tool Workshop Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
Key Features: Industry standard cone wrenches with unmatched performance,The Y-head design puts material where it is needed for strength and durability,Military grade phosphate finish ensures an accurate fit and consistent quality,Thin enough to be used on the narrowest of cones,High strength tool steel,Long vinyl dipped handle for leverage and comfort,Made in the USA and covered by Park Tool's legendary limited lifetime warranty.
A worn chain shifts poorly and wears sprockets at an accelerated rateThe CC-3 is a Go / No-Go gauge designed to accurately indicate when a chain reaches 0.75% and 1% wear - the point at which most chain manufacturers suggest replacementThe chain should be replaced soon if the 0.75% side fits into the chain, before other drive train components also start to wear out fastIf the 1% side fits into the chain, the chain is worn out and should be replaced immediatelyMade from precision, laser cut steelConsider that if you replace a chain because of wear other vital drive-chain components may need to be renewed too10-speed compatible
To use, just hang the head of the spoke in the oblong hole and read its length on the scale. For crank cotters and ball bearings, it works just like a gauge for drill bits.
Precision sizing and a military grade industrial phosphate finish ensure an accurate fit and consistent quality.
Park Tool Bladed Spoke Holder BSH-4 A simple yet essential tool for keeping your spokes in check when truing your wheels, the Bladed Spoke Holder BSH-4 will ensure no twists or bends during realignment. Valuable Wheel-Building Aid Suitable for holding a variety of different sized bladed spokes, the holder is equipped with 4 slots to holder your spokes in place while vital repairs are made. It also doubles up as a bladed spoke straightening device when used in conjunction with a spoke nipple wrench, to make sure your wheel remains a wind-cheater and not an egg beater. The Bladed Spoke Holder BSH-4 may look basic, but it proves its worth in keeping your wheels and spokes in check. Features: Compatibility: Spoke Blades from 0.8 mm to 2 mm Width Buy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
Fitted with four slots to hold a variety of different sized spokes, the BSH-4 ensures they stay strong and in place while you go about your necessary realignment. Pulling double duty as a spoke straightener when used alongside a spoke nipple wrench, the Bladed Spoke Holder BSH-4 from Park Tool does all it can to make sure your spokes and wheels remain in check.
A must have bench top accessory that keeps small parts accessible and all in one place15 cm diameter parts bowl with an extra strong magnet to stop you loosing vital component parts on the floor, under the workbench, or in the grass
Park Tool Pin Spanner (SPA-2)Bringing you excellent versatility at a budget-friendly price, the SPA-2 Pin Spanner works on a wide range of crankset lock rings and freewheel cone adjusters. Made from durable carbon tool steel that’s dipped in vinyl for a comfortable grip, Park Tool colour codes each tool so you can quickly find the size you need.Features: Material: Carbon Tool Steel with Vinyl-dipped handle Fits one-key release retaining rings on Shimano® and Campagnolo® cranksets and the adjusting cone on most freewheel clusters (not freehubs) Adjusts to a wide range of pin hole widths Pin diameter is nominally 0.090" (2.3mm)Buy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
Part of a range of taps to cover all normal needs on a bikeMade of high carbon steel, precision ground and hardenedFor cleaning out and repairing threadsFits into any conventional tap handle10 x 1 mm size is for derailleur hanger.
Key Features: Industry standard cone wrenches with unmatched performance,The Y-head design puts material where it is needed for strength and durability,Military grade phosphate finish ensures an accurate fit and consistent quality,Thin enough to be used on the narrowest of cones,High strength tool steel,Long vinyl dipped handle for leverage and comfort,Made in the USA and covered by Park Tool's legendary limited lifetime warranty.
The Park Tool cone spanner has been designed to give maximum usefulness and versatility at the lowest possible cost. Tough, high carbon tool steel is used on each tool to ensure long life. Its handle is vinyl coated to give a good grip and each pin spanner is colour coated for easy recognition.
Key Features: Industry standard cone wrenches with unmatched performance,The Y-head design puts material where it is needed for strength and durability,Military grade phosphate finish ensures an accurate fit and consistent quality,Thin enough to be used on the narrowest of cones,High strength tool steel,Long vinyl dipped handle for leverage and comfort,Made in the USA and covered by Park Tool's legendary limited lifetime warranty.
Key Features:The #764 pilot is used when facing BB86/92 bottom bracket shells and reaming is not required.,Used in conjunction with the HTR-1 Head Tube Reaming and Facing Set, 690-XL Facing Cutter and 750.2 Centering Cone Adapter..
Park Tool Axle Vice AV-1The AV-1 allows you to hold an axle in place using a bench vise, so it will not turn while work is done on the hub.Features:2 different diameter receptacles for front and rear axles Simple to use - just insert axle into proper diameter opening and tighten bench viseBuy Park Tool Workshop Accessories from Chain Reaction Cycles, the World's Largest Online Bike Store.
The AV-1 allows you to hold an axle in place using a bench vise, so it will not turn while work is done on the hub.
A selection of essential Metric hex wrenches in a convenient folding packageOne piece composite handle is comfortable lightweight and slip resistant - and 40% stronger than steelWrenches are made from high torque Bondhus Protanium industrial quality tool steel for a long life1.5 mm 2 mm 2.5 mm 3 mm 4 mm 5 mm and 6 mm size hex wrenches
Key Features: Two-sided spoke wrench is designed for Mavic wheel sets.,Long handle gives good leverage for stubborn spoke nipples., Fits both Mavic 5.65 mm threaded eyelets and 7 mm integrated nipples., Made in the USA and covered by Park's legendary limited lifetime warranty.,
The Park Tool CCW5C features both 14mm socket and 8mm hex wrench on a long, comfortable handle. The tool is suitable for many common square taper crank bolts. The 8 mm hex can also be used to install some Shimano SPD and SPD-SL pedals range.
Park Tool introduced the bicycle world to the three-way hex wrench set over 25 years ago. Updated in 2007, the Park AWS-1 and AWS-8 have colour-coded hex wrenches that allow sizes to be quickly identified, as well as a redesigned centre handle that fits perfectly in the palm of the hand. The hexes are made from Bondhus Protanium industrial steel and are hardened and tempered for long life. The Park Tool AWS1 Hex Wrench Tool includes 4mm, 5mm and 6mm hex key wrenches.