The tool is pulled through the frame until the flared ends snap in behind the cup. A blow on the tool head removes the cup.
The Park Tool FAG2 Frame Alignment Gauge helps solve the problem of many bicycles not shifting or tracking properly. This can be the result of the front and rear wheels not being in line with the frame. If these conditions still exist after wheel and derailleur adjustments, the seat stays, chain stays, and rear drop-outs of the frame may be misaligned. For years the accepted method to check the alignment of the rear drop-out was to run a string on either side. This method does work to some extent. However, it is not accurate because the measurement is not taken at the drop-out. With the Park Tool Frame Alignment Gauge the alignment can be checked quickly and accurately at the drop-out. Retractable pointer to fit all sizes and types of bicycles.
Top quality cable cutters for inner wires and outer casing, including index gear cablesPrecision ground cutting jaws make for a clean cut every timeCold forged and heat treated steel handles for massive strengthDual density moulded grips are contoured for comfort and controlBuilt in crimper for cable end capsForming hole for reforming cable housing and ferrulesA wire latch holds the handles together for storage
Key Features:The MT-40 is a high quality, folding take-along tool.Features forged aluminum side plates.Hardened and plated tools.Smooth ergonomic operation.2.5, 3, 4, 5, 6 and 8mm hex wrenches.T25 & T30 Torx® compatible driver.Combo cross/straight tip screwdriver.CO2 cartridge inflator adapter.Key ring holder.243 grams.
Park Tool Oversized Adjustable Saw Guide SG-7.2 Accurately guides a hacksaw to cut aero-shaped seat masts and seat posts up to 2.75"" (70mm), as well as fork steerer tubes and other round tubes from 1-1/16"" to 1-3/4"" (27mm to 45mm). The SG-7.2 features two different cutting slots — standard and carbon cutting blade widths — in a hardened steel body with moulded contact points to protect tubes and frames.Features: The SG-7.2 cutting guide is a specially shaped guide, designed specifically to accept aero-shaped seatmasts and seatposts up to 3.5 inches (89 mm) deep The guide can also accept round tubes from 1-1/4 inch to 1-3/4 inch (32 mm to 45 mm) in diameter Two cutting slots are provided, one for standard saw blades and one for thicker, carbon specific blades Hardened steel body with moulded contact points to protect tubes and frames Made in the USA and covered by Park Tool's legendary limited lifetime warrantyBuy Park Tool Tools from Chain Reaction Cycles, the World's Largest Online Bike Store.
It features a complete metal internal construction, ensuring reliability and durability.
The RT-2 is specially designed for removing 1-1/4 and 1.5 inch head cupsThe flared end fits through the head tube and snaps behind the cup allowing the cup to be removed with a tap of a hammerDurable heat treated alloy steel with nickel finish for long lifeThe new RT-2 does not replace the RT-1 Head Cup Remover although similar in appearance the two tools are designed to work on different size head cupsAlso suitable for may motorcycle headtubes
The SG-7.2 features two different cutting slots — standard and carbon cutting blade widths — in a hardened steel body with moulded contact points to protect tubes and frames.
These workshop quality tools are made from chrome vanadium steel making them tough and durable so they last a lifetime of use.
Key Features:Designed and built to install and remove BB30 bearings,The BBT-30.4 features a bushing set used in conjunction with a head cup press to quickly and precisely press the BB30 and PF30 bearings into the bottom bracket shell,The included BB30 bearing remover works from inside the shell to easily push out bearings,Updated to also remove PressFit 30 (PF30), EVO 386, BBright-Ö and PF121,Made in the USA and covered by Park Tool's legendary limited lifetime warranty.
The strength of the Park Tool CN10 comes from its heat-treated and cold-forged steel handles, which feel powerful and dependable in your hand. Its precision ground cutting jaws ensure the smoothest and sharpest cut with every bite, making for that level of quality workmanship that Park Tool wants its users to experience. Providing comfort with quality, the handles are covered by dual-density moulded grips. These are contoured for supreme ergonomic control while you cut your inner or outer cables or crimp your end caps with the tool's built-in crimper. Held tightly together when not in use with its wire handle latch, this is a precise and durable cable cutter that any garage or home workshop should not be without.
Park Tool Cable & Housing Cutter (CN-10)The CN-10 Cable and Housing Cutter from Park Tool has been designed to cut through bicycle cables and housing with ease. A firm favourite from Park Tool, this is an essential no-nonsense maintenance tool that every cycling enthusiast needs in their kit. Features:Strong, durable steel handlesPrecision ground cutting jaws for a clean cutBuilt-in crimper for cable end caps and forming hole for reforming housing ends and housing ferrulesWire latch holds handles together when not in useUse: Bicycle cables and housingBuy Park Tool Workshop Tools from Chain Reaction Cycles, the World's Largest Online Bike Store.
Park Tool Preset Torque Driver (PTD-5)This shop quality pre-set torque driver limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The PTD-5 features all metal internal construction with a comfortable, ergonomic composite moulded grip. Each tool is assembled and calibrated at The Park Tool factory in Minnesota. Features: Pre-set to 5 Nm ¼ inch hex drive Includes 3, 4, 5mm and T25 bits stored in the handle Limits torque applied to fasteners while rotating clockwise All metal internal construction for long lifeBuy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
Park Tool Preset Torque Driver PTD-6This shop quality pre-set torque driver limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The PTD-6 features all metal internal construction with a comfortable, ergonomic composite moulded grip. Each tool is assembled and calibrated at The Park Tool factory in Minnesota. Features: Pre-set to 6 Nm ¼ inch hex drive Includes 3, 4, 5mm and T25 bits stored in the handle Limits torque applied to fasteners while rotating clockwise All metal internal construction for long lifeBuy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
This shop quality pre-set torque driver limits torque applied to fasteners, preventing over-tightening and damage to lightweight components.
Held securely in place with magnets and top retainer legs, the precision extruded aluminium built insert has 9 standard jaw openings, (5, 9, 10, 12, 14, 20, 25, 30, and 36mm) including one for holding hydraulic tubing. Easily secured to your vice, the Axle & Spindle Vice Insert AV-5 offers great hold for carrying out hub maintenance and other essential repair work.
Park Tool Socket and Bit Set (SBS-1.2)Coming with all the common sized tool heads for getting the job done, Park Tool has created its SBS-1.2 18-piece Socket and Bit Set from a strong and hard-wearing steel so you can rely on it for many years to come. This bike-specific kit also comes in a convenient plastic tray so you can keep all the pieces organised and held together in your toolbox drawer.Features: Material: Chrome Vanadium Steel 3, 4, 5, 6, 8 and 10mm hex bits Long Reach 5 and 6mm hex bits Long Reach T25, T30 and T40 Torx style bits 8, 9, 10, 13, 14, 15mm and 1" sockets (The 1" socket fits various Park Tool Freewheel, Cassette Lockring, and Bottom Bracket tools) Convenient bit and socket holder tray included All sockets and bits are 3/8" drive Sockets Available To Purchase Separately: YesBuy Park Tool Workshop from Chain Reaction Cycles, the World's Largest Online Bike Store.
This Park Tool bearing press kit is equipped with one bottom bracket bearing remover and two bushings that will assist with the fitting of new bearings (separately sold headset press tool also required to install pressfit bearing/cups). Ideally suited to removing and replacing BB30, PressFit 30 (PF30), 386EVO, BBright and PF121 systems, this pack will help you to get the job done in no time at all. An up-to-date version of Park Tool's BBT-30.3, this set gives a longer length to work with wider fat bottom bracket shells, making it a fantastic tool to add to any garage or professional bike workshop. How To Use: To remove the bearing, the remover is fed through the shell until the flat head goes into the opposite side bearing. Once engaged, the tool's plastic guide will fit into the near-side shell opening to hold the tool steady while you tap the handle end firmly with a hammer, until the bearing pops out. To install new bearings, the bundled bushings (included) are used with a headset press (not included) to quickly and accurately press the bearings into the shell.
The SG-7.2 cutting guide is a specially shaped guide, designed specifically to accept aero-shaped seatmasts and seatposts up to 3.5 inches (89 mm) deepThe guide can also accept round tubes from 1-1/4 inch to 1-3/4 inch (32 mm to 45 mm) in diameterTwo cutting slots are gived, one for standard saw blades and one for thicker, carbon specific bladesHardened steel body with moulded contact points to priotect tubes and frames.
Precision ground cutting jaws for a clean cut every time Cold forged and heat treated steel handles for massive strength Dual density moulded grips for comfort and control Built in crimper for cable end cap Forming hole for reforming housing ends and housing ferrules Quite simply the best cutters money can buy